Warning: mkdir(): No space left on device in /www/wwwroot/new9.com/func.php on line 127

Warning: file_put_contents(./cachefile_yuan/65555501.com/cache/a1/104c4/de274.html): failed to open stream: No such file or directory in /www/wwwroot/new9.com/func.php on line 115
Fiber Optical Multiplexer,Interface Converter,Network Switches,TDM over IP-Fctel Technology Co.,Ltd




  • 黄瓜下载官网,黄瓜AVAPP,黄色视频黄瓜视频,黄瓜视频在线观看入口

    Hello, Welcome to FCTEL Technology Co.,Ltd
    National service hotline:+086 0571-87007055/56/57 CN

    WE ONLY FOCUS ON TRANSMISSION AND ACCESS

    Products center

    framed E1-FE Converter

    Type:FCC-E1fF1 Message

    Description:1channel framed E1 - FE converter ，N * 64k rate setting ，With E1 loopback detection function

    Product Description
                  This interface converter is based on FPGAproviding one framed E1 interface and one Ethernet interface to achieve 10/100base-T Ethernet data transmission on the E1 channel. It is a high performance self-learning Ethernet bridge. This device is the extension device of Ethernet using network (PDH/SDH/Microwave) that provide E1 channel to achieve local and remote Ethernet interconnecting with serial interfaces at a lower cost. The device has inter-set loop test function to facilitate the project launching and daily maintenance.

    Functional Properties
    ◆   based on self -copyright  IC 
    ◆   Can realize monitor and control of remote equipment OAM management data did not  take up user’s timeslot and save E1 bandwidth
    ◆   E1 supports any timeslot set the rate is 64K-2048K
    ◆   The local device can forced the remote device rate follow it
    Ø    Have the function of E1 interface loop back check avoid the converter crashed because of interface loop return;
    Ø Have indicator  when the device is power-off or E1 line is broken or lose signal;
    Ø Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
    Ø The Ethernet interface supports jumbo frames (2036 Bytes);
    Ø Inter-set dynamic Ethernet MAC address (4096) with local data frame filtering 

    Ø Ethernet interface supports10M/100M half/full duplex auto- Negotination and AUTO-MDIX

          (crossed line and straightly connected line self-adaptable );

    Ø Have Ethernet monitor self-reset function the equipment will not dead
    Ø Can achieve the remote device setting any 5 mode of Ethernet and can closed the AUTO-MDIX function; 
    Ø Provide 2 clock types: E1 master clock and E1 line clock;

    Ø Have three Loop Back Mode: E1 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote

          Ethernet interface Loop Back(REM) 

    Ø Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
    Ø Support SNMP Network Management;
    Ø Can realize monitor of remote equipment temperature and voltage from local equipment;  
    Ø Can form the structure: Ethernet E1 Bridge(A)－－-E1 Optical Fiber Modem(B)－－-Ethernet Optical Fiber Modem (C) 

    Ø   Can form the structure: Ethernet E1 Bridge(A)－－-Optical Ethernet Modem(B)－－-Ethernet Optical Fiber Transceiver (C) 

          can manage (B) and (C) at (A)


    Technical Parameters

    ◆   E1 Interface

        Interface Standard:      comply with protocol G.703;
        Interface Rate:             n*64Kbps±50ppm;
        Interface Code:            HDB3;

        E1 Impedance:             75Ω (unbalance) 120Ω (balance);

        Jitter tolerance:            In accord with protocol G.742 and G.823

        Allowed Attenuation:   0~6dBm

    u Ethernet interface (10/100M)

        Interface rate:              10/100 Mbps half/full duplex auto-negotiation

        Interface Standard:      Compatible with IEEE 802.3 IEEE 802.1Q (VLAN)

        MAC Address Capability: 4096

        Connector:                  RJ45 support Auto-MDIX

    u   Power

        Power supply: AC180V ~ 260V；DC –48V；DC +24V

        Power consumption: ≤10W

    u   Dimension          

     

        Product Size :       216X140X31mm( WX DXH))

        Simple packaging : 274X193 X84mm ( WX DXH)

        Piece Weight: 1.1KG

    u  Working environment

        Working temperature: -10°C ~ 50°C
        Working Humidity:        5%~95 % (no condensation)

        Storage temperature:   -40°C ~ 80°C
        Storage Humidity:         5%~95 % (no condensation)

     

    Application Scheme

    Applications 1

    Applications 2

    Applications 3

     

    DataSheet Download
    
    网站地图